<![CDATA[NCDubs | VW Audi Porsche Performance News & Tuning Forums]]> http://www.forums.ncdubs.org en Thu, 09 Sep 2010 01:27:09 GMT vBulletin 60 http://forums.ncdubs.org/images/chestnut/misc/rss.jpg <![CDATA[NCDubs | VW Audi Porsche Performance News & Tuning Forums]]> http://www.forums.ncdubs.org BBS RS/Enkei EK98 15x8 wheels $600 obo http://www.forums.ncdubs.org/showthread.php?t=19585&goto=newpost Thu, 09 Sep 2010 01:14:35 GMT These wheels are Enkei EK98's (they look a lot like BBS RS's and have bbs centercaps)
Good overall condition
15x8
5x120 bolt pattern
+15mm offset
$550
The price is OBO, and I might be open to trades specifically for some nice 4x100 wheels

]]> Wheels rubadubbin http://www.forums.ncdubs.org/showthread.php?t=19585 VIR Holiday Laps Charity GTG/Event *FEELER* http://www.forums.ncdubs.org/showthread.php?t=19584&goto=newpost Thu, 09 Sep 2010 00:17:00 GMT This is a bit early, but I want to gauge interest since there's been a bit of conversation about putting together a forum wide event.

The Skinny:
Every year Virginia International Raceway (VIR) holds a charity drive for the Salvation Army. For a $25 donation of toys, canned food, or cash you can drive your car on VIR's full course behind the pace car for one session (~20mins which is ~7laps). $50 would get you two sessions and so on. I've talked with the folks at VIR and if we can get "close to 35 or more" cars together we could go out together as one big group.

Date/Time:
Friday, November 12th, 9am-4pm

More Info:
VIR

VIR is about 1 hour from GSO and 1.5 hours from Raleigh.


By the way, this is one of the pace cars:
]]> zooyork155 http://www.forums.ncdubs.org/showthread.php?t=19584 Need tools for axle install http://www.forums.ncdubs.org/showthread.php?t=19583&goto=newpost Thu, 09 Sep 2010 00:12:05 GMT Got a new axle on the way and no tools to put it on. Anyone in the boone/banner elk area have the tools to replace a mk4 axle . Will provide beer for... Got a new axle on the way and no tools to put it on. Anyone in the boone/banner elk area have the tools to replace a mk4 axle . Will provide beer for loaning of tools, will provide more beer if ya help me do it in your garage. ]]> Gibson19 http://www.forums.ncdubs.org/showthread.php?t=19583 So Who Has One of These? http://www.forums.ncdubs.org/showthread.php?t=19582&goto=newpost Thu, 09 Sep 2010 00:01:18 GMT I'm racing Saturday and get one of these fine t-shirts to boot!

Anyone else signed up from wilmy wood? hit me up and we'll meet up down there,PM me and I'll send ya my cell #, no way am I posting it!
Attached Images
File Type: jpg vw_resized.jpg (44.3 KB)
]]> jetta-the-hut http://www.forums.ncdubs.org/showthread.php?t=19582 H2Oi Club Parking http://www.forums.ncdubs.org/showthread.php?t=19581&goto=newpost Wed, 08 Sep 2010 21:59:56 GMT Is anyone arranging the club parking this year? I know Dirk did it last year. I'm def. in if anyone is. ]]> Azraell http://www.forums.ncdubs.org/showthread.php?t=19581 H2oI action! http://www.forums.ncdubs.org/showthread.php?t=19579&goto=newpost Wed, 08 Sep 2010 17:45:35 GMT Who's going and what are you bringing.
just wanna see who's heading up so i can keep an eye out ;)
Staying at the serene on 122'nd

]]> Jeffy Dahmer http://www.forums.ncdubs.org/showthread.php?t=19579 MKIV assortment http://www.forums.ncdubs.org/showthread.php?t=19578&goto=newpost Wed, 08 Sep 2010 15:24:38 GMT I've got some MKIV goodies for sale since mine got totaled and now I'm on a MKII.

Brand spankin' NEW OEM MKIV Golf hood, still in the factory black primer - $60:gt-happyup:

MKIV 2002 GTI Monte Carlos, set of 4, pretty damn good shape - $500 for all of 'em, no tires mounted on them
As far as the wheels go, they are in the attic in my parents garage, they are straight and clean I just don't have the pics of them any more. These are the monte carlos with the machined aluminum 5 spoke face with the anthracite recess with rivets. Apparently they changed the style for later MKIVs. 5x100 for anyone that isn't aware of that.

And last but not least... a MKIV Jetta EURO front bumper rub strip - $20, painted 20thAE blue - Will NOT fit a GTI/Golf... trust me, I found out the hard way when I was shipped the wrong part and had it painted. Anyhow, I have no use for it any more at all, never been used.

I live in Raleigh, parts are in Creedmoor, but I can pick them up and have them ready in a few hours notice most of the time or can set up a time to meet me out there and look at whatever you need to see. ]]> Parts Rabbit180 http://www.forums.ncdubs.org/showthread.php?t=19578 Remixed Rollers http://www.forums.ncdubs.org/showthread.php?t=19577&goto=newpost Wed, 08 Sep 2010 15:20:33 GMT So after Hellaflush Remix on July 30th at the Sun Life Stadium, we decided to go for a small drive down to the South Beach area for some food and... So after Hellaflush Remix on July 30th at the Sun Life Stadium, we decided to go for a small drive down to the South Beach area for some food and drinks. Needless to say, we took the opportunity to take some sick rollers since both cars were clean and looking good. On a side note, when I first saw the pictures of Marcela’s MKIV Jetta all I could think was how “wet” her car looked. Probably had something to do with the wax it got the night before.

Rezmoto.com
Facebook.com/rezmoto











]]> Rezmoto Rezmoto http://www.forums.ncdubs.org/showthread.php?t=19577 Who can cut keys? http://www.forums.ncdubs.org/showthread.php?t=19576&goto=newpost Wed, 08 Sep 2010 14:12:57 GMT Who can cut non immobilized keys. Who can cut non immobilized keys. ]]> Main Forum kcfoxie http://www.forums.ncdubs.org/showthread.php?t=19576 Hey! 2.0 Golf NC State student from Jersey! Where are you? http://www.forums.ncdubs.org/showthread.php?t=19575&goto=newpost Wed, 08 Sep 2010 12:06:15 GMT Hope you didn't lose the card and found the forums (now that we're back). ]]> Raleigh, Durham, Cary kcfoxie http://www.forums.ncdubs.org/showthread.php?t=19575 Machine shop recommendations http://www.forums.ncdubs.org/showthread.php?t=19572&goto=newpost Tue, 07 Sep 2010 17:49:24 GMT I have a 12v VR6 motor I'm tearing down in order to build a turbo motor for my Corrado. I'm looking for a shop in the eastern half of NC to do machine work for me (overbore on the block, head work, etc). Anyone have any recommendations?

I'm in Greenville but am looking for a reputable shop so I don't mind shipping the parts or traveling as long as I know it will get done right. Thanks! ]]> Main Forum weaselwhy7@yahoo.com http://www.forums.ncdubs.org/showthread.php?t=19572 <![CDATA[Looking For Borbet Type S's]]> http://www.forums.ncdubs.org/showthread.php?t=19570&goto=newpost Tue, 07 Sep 2010 04:25:49 GMT Lookin' for some Borbet Type S's (4). 17's, 7.5-8", 5/112. ]]> Wheels 00Passout http://www.forums.ncdubs.org/showthread.php?t=19570 <![CDATA[Notch Job's]]> http://www.forums.ncdubs.org/showthread.php?t=19569&goto=newpost Sun, 05 Sep 2010 19:38:40 GMT Anyone know of a place or someone that they know who can hook me up with a notch job in or near Greensboro. I am not asking for a free notch BTW just... Anyone know of a place or someone that they know who can hook me up with a notch job in or near Greensboro. I am not asking for a free notch BTW just wondering if any of you have gotten it done anywhere around here. Thanks. ]]> Greensboro, Winston-Salem Nova http://www.forums.ncdubs.org/showthread.php?t=19569 <![CDATA[FS: 13x8 silver Rota RB's with tires]]> http://www.forums.ncdubs.org/showthread.php?t=19568&goto=newpost Sat, 04 Sep 2010 19:06:52 GMT SOLD!

i have a set of 4x100 rota RB's that i have no use for anymore, looking to sell to clear space in my garage



no curb rash at all, the tires have good tread left

$400 picked up in charlotte NC,

PM me here or for a faster responce email me at onelowcabrio @ gmail.com ]]> Wheels OnelowcabriO http://www.forums.ncdubs.org/showthread.php?t=19568